active 2023-08-15 → 2026-04-21 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 981 days from 2023-08-15 to 2026-04-21. Pushes: 19 total, peak 10 in a day. Pull requests: 30 total, peak 5 in a day. Issues: 51 total, peak 2 in a day. Comments: 66 total, peak 4 in a day. Stars: 357 total, peak 4 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| AndrewEllis93 | 39 | 19 | 11 | 5 |
| SuhbatDaRobot | 7 | 0 | 1 | 4 |
| dependabot[bot] | 7 | 0 | 5 | 2 |
| theschles | 5 | 0 | 0 | 5 |
| skyaee | 4 | 0 | 0 | 3 |
| Jomik | 4 | 0 | 0 | 2 |
| PhilippMolitor | 3 | 0 | 2 | 1 |
| Vojtak42 | 3 | 0 | 2 | 0 |
| krautech | 3 | 0 | 0 | 1 |
| quarkvalk | 3 | 0 | 3 | 0 |
| Yatin-Khurana | 2 | 0 | 0 | 2 |
| IvanGutowskiSmith | 2 | 0 | 0 | 1 |
| bassamanator | 2 | 0 | 0 | 2 |
| nerdhunt | 2 | 0 | 0 | 1 |
| ghylander | 2 | 0 | 1 | 1 |
| pvginkel | 2 | 0 | 0 | 2 |
| EkiciLP | 2 | 0 | 0 | 0 |
| clearbucketLabs | 2 | 0 | 0 | 2 |
| PuterPro | 2 | 0 | 0 | 1 |
| Mazaka2018 | 1 | 0 | 0 | 1 |
Recent activity
Latest issues, pull requests and releases
- Issue#173thomasfinstad2026-03-04 14:27INFO: Pattern style PA calibration built into Orca
- Issue comment#169stablestud2026-02-12 10:20TEST_SPEED macro issues GET_POSITION while robot in motion
- Issue comment#73Yatin-Khurana2025-12-21 08:05Add note about "step_pulse_duration" directive required for Mellow boards to layer shifting article
- Issue comment#161theschles2025-10-05 19:04Pressure Advance: Worry about inter-line gaps near-90 degree turns?
- Issue#168lollo11882025-09-17 07:25[Clarification] Cura Slicer - Volumetric Max Flow Rate and Max Print Speed
- Issue comment#161theschles2025-09-04 06:01Pressure Advance: Worry about inter-line gaps near-90 degree turns?
- Issue#167cirracus2025-08-29 02:27[Suggestion] Extrusion Multiplier selection and judgement for light colour PLA - use sharpie
- Issue comment#161theschles2025-08-21 17:20Pressure Advance: Worry about inter-line gaps near-90 degree turns?
- Issue#166megamandal2025-08-21 04:17non 2mm VFA
- Issue#164Jammer-hammer2025-07-24 09:26Small correction to Determining Motor Currents. Cited RMS amperage of TMC2209 (2a>1.7A).
- Issue#163Fercho56562025-07-17 02:42TEST_SPEED macro always outputs the same X and Y values even if skipping occurs
- Issue comment#161theschles2025-07-16 21:31Pressure Advance: Worry about inter-line gaps near-90 degree turns?
- Issue comment#161theschles2025-07-02 23:37Pressure Advance: Worry about inter-line gaps near-90 degree turns?
- Issue comment#162theogayar2025-07-01 15:23Removed accel_to_decel from the SET_VELOCITY_LIMIT in TEST_SPEED.cfg
- Pull request#160Vojtak422025-05-21 11:45
- Pull request#159Vojtak422025-05-21 11:37
- Issue comment#121dowatugkins2025-05-08 15:49There is an Error in the calculation of the new_rotation_distance in the Tuning Chapter Extruder Calibration
- Issue#158fekete002025-05-06 03:09Add troubleshooting for under-extrusion after overhangs
- Issue comment#157kiwidave722025-05-01 10:53Linear Advance - PrusaSlicer
- Issue#157Vojtak422025-05-01 09:10Linear Advance - PrusaSlicer
- Issue#155Rudis12612025-04-02 19:41[Suggestion] How the hell to tune seem / gap
- Issue comment#142batista162025-04-01 12:09TEST_SPEED: "Move out of range: 356.000 350.000 60.000 [0.000]"
- Issue comment#121brymck12025-03-21 13:25There is an Error in the calculation of the new_rotation_distance in the Tuning Chapter Extruder Calibration
- Pull request#154Fenikkusu2025-03-18 15:44
- Pull request#153AndrewEllis932025-03-14 16:16
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 357 stars here means stars gained during the window, not the repo's star count.