active 2024-05-21 → 2025-11-06 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 535 days from 2024-05-21 to 2025-11-06. Pushes: 11 total, peak 6 in a day. Pull requests: 1 total, peak 1 in a day. Issues: 11 total, peak 9 in a day. Comments: 6 total, peak 2 in a day. Stars: 2 total, peak 1 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| produceconsumerobot | 27 | 11 | 1 | 5 |
| nitin710 | 4 | 0 | 0 | 1 |
Recent activity
Latest issues, pull requests and releases
- Issue#25nitin7102025-11-06 23:04creating injection moulded case
- Issue comment#19produceconsumerobot2024-11-16 00:10SwissArmyCase: Make case supports on the long edge wider to span full distance between connector pads
- Issue#19produceconsumerobot2024-11-16 00:10SwissArmyCase: Make case supports on the long edge wider to span full distance between connector pads
- Issue#19produceconsumerobot2024-10-21 23:51SwissArmyCase: Make case supports on the long edge wider to span full distance between connector pads
- Issue comment#9produceconsumerobot2024-10-21 23:47Make the SwissArmyCase slider and screws thinner for the HUZZAH32
- Issue#9produceconsumerobot2024-10-21 23:47Make the SwissArmyCase slider and screws thinner for the HUZZAH32
- Issue#11produceconsumerobot2024-10-21 23:47SwissArmyCase: Add 4 small pillars/lips to hold Feather from unplugging out of Emotibit in case
- Issue comment#12produceconsumerobot2024-10-21 23:46SwissArmyCase: Consider if there's a way to make the reset button finger pushable
- Issue#12produceconsumerobot2024-10-21 23:46SwissArmyCase: Consider if there's a way to make the reset button finger pushable
- Issue#13produceconsumerobot2024-10-21 23:45SwissArmyCase: Add case support feat to prevent bending emotibit PCB
- Issue#14produceconsumerobot2024-10-21 23:45SwissArmyCase: Add clips onto case body to hold onto EmotiBit PCB
- Issue#15produceconsumerobot2024-10-21 23:45SwissArmyCase: Make USB hole smaller
- Issue#16produceconsumerobot2024-10-21 23:45SwissArmyCase: Consider shrinking slider hole width to better match slider width
- Issue#17produceconsumerobot2024-10-21 23:44SwissArmyCase: Chamfer slider top outer corners to prevent catching on case
- Issue comment#18produceconsumerobot2024-09-08 13:48Upgrade swiss army case
- Issue comment#18produceconsumerobot2024-05-22 00:19test 1 for training
- Pull request#18produceconsumerobot2024-05-21 23:30
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 2 stars here means stars gained during the window, not the repo's star count.