copy EnragedRabbitProject
active 2023-08-15 → 2026-08-14 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 1096 days from 2023-08-15 to 2026-08-14. Pushes: 0 total, peak 0 in a day. Pull requests: 3 total, peak 1 in a day. Issues: 8 total, peak 1 in a day. Comments: 5 total, peak 1 in a day. Stars: 821 total, peak 9 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| o-lampe | 2 | 0 | 0 | 1 |
| Zephyrus67 | 2 | 0 | 0 | 0 |
| ningpj | 1 | 0 | 0 | 0 |
| k1-801 | 1 | 0 | 0 | 0 |
| dedekcz | 1 | 0 | 0 | 1 |
| ammoniak | 1 | 0 | 0 | 1 |
| jwhite | 1 | 0 | 1 | 0 |
| ddellant | 1 | 0 | 0 | 1 |
| Kadah | 1 | 0 | 0 | 1 |
| slaesh | 1 | 0 | 1 | 0 |
| VinnyCordeiro | 1 | 0 | 0 | 0 |
| dejanmaksa | 1 | 0 | 0 | 0 |
| DuckersMcQuack | 1 | 0 | 0 | 0 |
| GarthSnyder | 1 | 0 | 1 | 0 |
Recent activity
Latest issues, pull requests and releases
- Issue#147ningpj2024-11-06 15:21no_toolhead_sensor filament load sequence to extruder gear - enhancement
- Issue#208DuckersMcQuack2024-07-29 08:50[non issue] ERCF name origin?
- Issue comment#207ddellant2024-06-04 22:52Enraged Rabbit Carrot Feeder for Bambu Lab P1S
- Issue#207dejanmaksa2024-03-16 12:14Enraged Rabbit Carrot Feeder for Bambu Lab P1S
- Issue#202Zephyrus672024-01-21 01:14Official CW2 support.
- Pull request#206slaesh2024-01-17 12:41
- Issue comment#204Kadah2023-12-27 04:26tolerances of .stl parts good for resin printing?
- Issue comment#204o-lampe2023-11-08 08:16tolerances of .stl parts good for resin printing?
- Issue#205VinnyCordeiro2023-11-06 23:50Warning about EOL of toolhead sensor component
- Pull request#156jwhite2023-10-30 02:33
- Issue comment#204ammoniak2023-10-26 06:40tolerances of .stl parts good for resin printing?
- Issue#204o-lampe2023-10-16 11:18tolerances of .stl parts good for resin printing?
- Issue#203k1-8012023-10-07 04:12Documentation: 80T Pulley centering instructions
- Issue comment#202dedekcz2023-09-30 16:39Official CW2 support.
- Issue#202Zephyrus672023-09-14 14:04Official CW2 support.
- Pull request#201GarthSnyder2023-08-22 23:37
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 821 stars here means stars gained during the window, not the repo's star count.