Snapmaker plugin for Cura 5
active 2023-08-17 → 2026-01-14 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 882 days from 2023-08-17 to 2026-01-14. Pushes: 4 total, peak 1 in a day. Pull requests: 7 total, peak 2 in a day. Issues: 11 total, peak 4 in a day. Comments: 9 total, peak 3 in a day. Stars: 17 total, peak 2 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| parachvte | 8 | 4 | 4 | 0 |
| tensile23 | 6 | 0 | 0 | 2 |
| AlexanderWMacFarlaneIV | 4 | 0 | 0 | 3 |
| macdylan | 2 | 0 | 2 | 0 |
| bbarenz | 1 | 0 | 0 | 1 |
| davide1a | 1 | 0 | 0 | 0 |
| VVeyy | 1 | 0 | 0 | 0 |
| hilmerhall | 1 | 0 | 0 | 0 |
| firebladed | 1 | 0 | 0 | 1 |
| mehdichaouch | 1 | 0 | 0 | 1 |
| JackTR1357 | 1 | 0 | 0 | 0 |
| sillyfrog | 1 | 0 | 1 | 0 |
| steveof2620 | 1 | 0 | 0 | 0 |
| PrinterKees | 1 | 0 | 0 | 0 |
| agodwin-44 | 1 | 0 | 0 | 1 |
Recent activity
Latest issues, pull requests and releases
- Issue comment#93agodwin-442026-01-14 04:38cannot save gcode err
- Issue#93VVeyy2025-12-29 05:03cannot save gcode err
- Issue#92PrinterKees2025-07-30 12:28Raft air gap setting
- Issue comment#88bbarenz2024-09-27 20:01Don't get a message "Send to <IP>"
- Issue comment#90AlexanderWMacFarlaneIV2024-05-05 20:24Build Plate Temperature Wrong
- Issue comment#90AlexanderWMacFarlaneIV2024-05-05 17:51Build Plate Temperature Wrong
- Issue comment#90AlexanderWMacFarlaneIV2024-05-05 17:49Build Plate Temperature Wrong
- Issue#90AlexanderWMacFarlaneIV2024-05-05 17:48Build Plate Temperature Wrong
- Pull request#89sillyfrog2024-04-21 21:42
- Issue comment#88firebladed2024-03-09 16:08Don't get a message "Send to <IP>"
- Issue#87davide1a2024-01-24 20:05First layer temps not right when sending via wifi
- Issue comment#76mehdichaouch2023-12-21 13:58Snapmaker Original
- Releaseparachvte2023-11-11 19:040.9.4
- Pull request#85parachvte2023-11-10 09:17
- Pull request#84parachvte2023-11-09 03:40
- Pull request#85macdylan2023-11-08 01:11
- Pull request#84macdylan2023-11-08 01:09
- Issue comment#83tensile232023-10-16 07:42Does not wait for temp on extruder change.
- Issue#50tensile232023-10-16 07:41Artisan always prints using the left extruder
- Issue#71tensile232023-10-16 07:36[FR] Use ufp files instead of gcode
- Issue#77tensile232023-10-16 07:35Cant connect to printer through wifi
- Issue#78tensile232023-10-16 07:35Snapmaker 2.0 Dual Print Issue
- Issue comment#79tensile232023-10-16 07:34Bed Misalignment
- Issue#83hilmerhall2023-10-15 00:41Does not wait for temp on extruder change.
- Pull request#82parachvte2023-10-11 03:01
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 17 stars here means stars gained during the window, not the repo's star count.