active 2023-10-23 → 2023-12-14 (UTC)
Complete coverage26,571 / 26,571 hourly files (100%) · 2 absent upstream2023-08-15 → 2026-08-26 (UTC)
Events
40
Pushes
7
Pull requests
0
Issues
18
Stars
0
Forks
0
Activity over time
Daily event counts in the loaded window
Line chart, 54 days from 2023-10-23 to 2025-07-25. Pushes: 7 total, peak 3 in a day. Pull requests: 0 total, peak 0 in a day. Issues: 18 total, peak 10 in a day. Comments: 13 total, peak 11 in a day. Stars: 0 total, peak 0 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| asfarley | 36 | 7 | 0 | 12 |
Recent activity
Latest issues, pull requests and releases
- Issue#12asfarley2025-07-25 04:15Can't tighten top screw attaching brake arm to shaft when enclosure top is attached
- Issue comment#11asfarley2025-07-25 02:39My angle magnets are too powerful! You cannot handle them!
- Issue#9asfarley2023-12-14 06:02PCB corner is too close to nut holding torque-plate
- Issue comment#9asfarley2023-12-14 06:02PCB corner is too close to nut holding torque-plate
- Issue#3asfarley2023-12-14 06:01Thread on throttle-arm torque plate causes binding with nut
- Issue comment#3asfarley2023-12-14 06:01Thread on throttle-arm torque plate causes binding with nut
- Issue comment#4asfarley2023-12-14 06:01Knob handles rattle
- Issue#4asfarley2023-12-14 06:01Knob handles rattle
- Issue comment#7asfarley2023-12-14 06:00Bearing holes are too loose, or too tight
- Issue#7asfarley2023-12-14 06:00Bearing holes are too loose, or too tight
- Issue comment#8asfarley2023-12-14 05:59Thread on torque-plate damaged while press-fitting angle sense magnet
- Issue#8asfarley2023-12-14 05:59Thread on torque-plate damaged while press-fitting angle sense magnet
- Issue comment#11asfarley2023-12-14 05:51My angle magnets are too powerful! You cannot handle them!
- Issue comment#2asfarley2023-12-14 05:33Angle magnet holes are too tight
- Issue#2asfarley2023-12-14 05:33Angle magnet holes are too tight
- Issue#1asfarley2023-12-14 05:33Detent magnet holes are too loose
- Issue comment#1asfarley2023-12-14 05:33Detent magnet holes are too loose
- Issue comment#5asfarley2023-12-14 05:33Throttle-arm contacts casing on upper end
- Issue#5asfarley2023-12-14 05:33Throttle-arm contacts casing on upper end
- Issue#10asfarley2023-12-14 05:32Throttle PCB connector should be horizontal, not right-angle
- Issue comment#10asfarley2023-12-14 05:32Throttle PCB connector should be horizontal, not right-angle
- Issue comment#6asfarley2023-12-14 05:31D holes on base-plate aren't threaded
- Issue#6asfarley2023-12-14 05:31D holes on base-plate aren't threaded
- Issue#11asfarley2023-12-13 03:04My angle magnets are too powerful! You cannot handle them!
- Issue#10asfarley2023-12-03 08:33Throttle PCB connector should be horizontal, not right-angle
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 0 stars here means stars gained during the window, not the repo's star count.