grblMAX core code and master Wiki
active 2023-08-15 → 2026-08-17 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 1099 days from 2023-08-15 to 2026-08-17. Pushes: 238 total, peak 3 in a day. Pull requests: 44 total, peak 2 in a day. Issues: 385 total, peak 29 in a day. Comments: 1,337 total, peak 16 in a day. Stars: 225 total, peak 14 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| terjeio | 902 | 236 | 10 | 546 |
| skasti | 77 | 0 | 5 | 54 |
| MrKapim | 69 | 0 | 0 | 65 |
| dresco | 54 | 0 | 1 | 49 |
| engigeer | 54 | 0 | 7 | 33 |
| karoria | 52 | 0 | 0 | 39 |
| Deltaplc | 46 | 0 | 0 | 40 |
| hanke-cnc | 39 | 0 | 0 | 22 |
| nickshl | 38 | 0 | 0 | 29 |
| distebia | 36 | 0 | 0 | 30 |
| MattMead166 | 30 | 0 | 0 | 28 |
| andrewmarles | 25 | 0 | 6 | 14 |
| Dietz0r | 25 | 0 | 2 | 16 |
| customsolutions | 22 | 0 | 0 | 22 |
| rvalotta | 16 | 0 | 0 | 9 |
| tcurdt | 14 | 0 | 0 | 8 |
| Nick507 | 13 | 0 | 0 | 3 |
| iLoveAndyBaker | 13 | 0 | 0 | 8 |
| AvatarBg111 | 12 | 0 | 0 | 11 |
| paukstelis | 11 | 0 | 0 | 7 |
Recent activity
Latest issues, pull requests and releases
- Issue#1002Alijambo2026-08-13 03:20M4 (dynamic/rate-adjusted) laser power not zeroed on G0 block immediately following a rate-adjusted G1 block
- Issue comment#991terjeio2026-07-26 04:51Laser power set-point not restored following feed-hold with "Disable Laser during hold" set to False
- Issue#971stefanpopa27021983-tech2026-06-20 04:08Cut plasma cnc
- Issue#959DimDimKo2026-05-25 23:41Warning [-Wmaybe-uninitialized] in gcode.c
- Issue comment#954spxwh2026-05-17 02:27There is an issue with using thread cycle G33.
- Issue#954spxwh2026-05-14 09:19There is an issue with using thread cycle G33.
- Issue comment#945Alois-S732026-05-10 09:57firmware Build
- Issue comment#766Aepx2026-05-09 13:54Homing question/request
- Issue#940etet1002026-04-26 12:24settings.c, settings_restore - G30 not stored?
- Pull request#939engigeer2026-04-15 06:41
- Issue comment#926XYartlab2026-04-06 05:03Is there a parameter that allows me to set the A-axis to display in degrees？
- Issue comment#816spxwh2026-04-05 10:01I want to try rigid tapping G33.1 or G84 on my mill using stepper spindle
- Issue comment#931XYartlab2026-04-03 10:16About control stream and mpg control
- Issue comment#931XYartlab2026-04-03 10:05About control stream and mpg control
- Pull request#933JasonTitcomb2026-04-02 11:57
- Issue#932andrewmarles2026-04-01 22:41modbus_send_rtu while(spin_lock); causing infinite loop.
- Pull request#928bullestock2026-03-31 18:46
- Pull request#858engigeer2026-03-18 06:33
- Issue comment#920terjeio2026-03-08 23:57Add core support for FLEXGPIO i2c Expander and Motor Alarm Expander Inputs
- Issue comment#918Edding3002026-03-02 21:54How to start with grblHAL?
- Issue comment#918Edding3002026-03-02 21:20How to start with grblHAL?
- Issue#919ViterOK-932026-03-02 03:13Setting NGC_PARAMETERS_ENABLE to Off results compiling errors
- Issue#918Edding3002026-02-27 16:15How to start with grblHAL?
- Issue#879terjeio2026-02-27 10:212-axis ganged Y (dual Y motors) Auto Square Issue
- Issue comment#870terjeio2026-02-27 10:17Feature Request: Linear Encoder / Scale Feedback for Closed-Loop CNC Control
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 225 stars here means stars gained during the window, not the repo's star count.