Firmware for the RX888mk2 Direct Sampling SDR
active 2024-05-11 → 2026-05-10 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 730 days from 2024-05-11 to 2026-05-10. Pushes: 103 total, peak 17 in a day. Pull requests: 5 total, peak 3 in a day. Issues: 77 total, peak 19 in a day. Comments: 51 total, peak 15 in a day. Stars: 0 total, peak 0 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
| Contributor | Contributions | Pushes | PRs | Comments |
|---|---|---|---|---|
| ringof | 233 | 103 | 5 | 48 |
| chatgpt-codex-connector[bot] | 4 | 0 | 0 | 3 |
Recent activity
Latest issues, pull requests and releases
- Pull request#98ringof2026-05-10 16:27
- Pull request#92ringof2026-05-10 04:33
- Issue comment#80ringof2026-05-09 02:24hw_smoke (test 30) and stop_start_cycle (test 32) fail, show 0 bytes, the stream doesn't restart after a stop
- Pull request#88ringof2026-05-08 23:20
- Pull request#87ringof2026-05-08 23:17
- Pull request#87ringof2026-05-08 23:17
- Issue comment#82ringof2026-02-26 23:29Soak: dma_count_reset always fails with 0x1006 (Population B)
- Issue#82ringof2026-02-19 23:26Soak: dma_count_reset always fails with 0x1006 (Population B)
- Issue#82ringof2026-02-19 23:26Soak: dma_count_reset always fails with 0x1006 (Population B)
- Issue#81ringof2026-02-19 23:26Soak: STARTFX3 occasionally fails to produce data (0x1005, Population A)
- Issue comment#80ringof2026-02-19 16:06hw_smoke (test 30) and stop_start_cycle (test 32) fail, show 0 bytes, the stream doesn't restart after a stop
- Issue#79ringof2026-02-19 03:56CLEAR_FEATURE(ENDPOINT_HALT) on EP 0x81 causes FX3 stop-command failures
- Issue comment#79ringof2026-02-19 03:56CLEAR_FEATURE(ENDPOINT_HALT) on EP 0x81 causes FX3 stop-command failures
- Issue comment#79ringof2026-02-19 03:31CLEAR_FEATURE(ENDPOINT_HALT) on EP 0x81 causes FX3 stop-command failures
- Issue#79ringof2026-02-19 03:22CLEAR_FEATURE(ENDPOINT_HALT) on EP 0x81 causes FX3 stop-command failures
- Issue comment#78ringof2026-02-19 02:22STARTFX3 missing CyU3PUsbResetEp causes EP1 data toggle desync across USB handle cycles
- Issue comment#78ringof2026-02-18 19:08STARTFX3 missing CyU3PUsbResetEp causes EP1 data toggle desync across USB handle cycles
- Issue comment#73ringof2026-02-18 11:47FX3 watchdog loops forever when host crashes without sending STOPFX3
- Issue#77ringof2026-02-18 11:47Rapid START/STOP cycling (no bulk reads) causes hard lockup on next STARTADC
- Issue comment#75ringof2026-02-17 18:00clock_pull mid-stream bricks device — requires power cycle
- Issue comment#75ringof2026-02-17 17:59clock_pull mid-stream bricks device — requires power cycle
- Issue#68ringof2026-02-17 07:06Make glUARTtoCPU_Handle, glConsoleInBuffer, glConsoleInIndex static in DebugConsole.c
- Issue comment#68ringof2026-02-17 07:06Make glUARTtoCPU_Handle, glConsoleInBuffer, glConsoleInIndex static in DebugConsole.c
- Issue#70ringof2026-02-17 06:59Make glVendorRqtCnt static in USBHandler.c
- Issue comment#70ringof2026-02-17 06:59Make glVendorRqtCnt static in USBHandler.c
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 0 stars here means stars gained during the window, not the repo's star count.