A python based service that receives sensor inputs and publishes them over REST (should work with any API but mainly tested with openHAB) or MQTT. It can also receive commands and perform an action (e.g. set a GPIO pin to HIGH). It currently supports Bluetooth, GPIO on Raspberry Pi, Amazon Dash buttons, command line scripts, and Roku IP address discovery.
active 2023-08-22 → 2026-03-08 (UTC)
Activity over time
Daily event counts in the loaded window
Line chart, 930 days from 2023-08-22 to 2026-03-08. Pushes: 20 total, peak 2 in a day. Pull requests: 35 total, peak 4 in a day. Issues: 19 total, peak 2 in a day. Comments: 77 total, peak 4 in a day. Stars: 7 total, peak 1 in a day.
- Pushes
- Pull requests
- Issues
- Comments
- Stars
Stars, PRs, issues and forks are under-captured in the later part of this window. GH Archive progressively stopped capturing non-push events during 2026 — −95% or worse by the end of the window. Every series here except Pushes fades for that reason, so a decline above reflects the archive, not this repository. Pushes stay reliable throughout, so read them, and the contributor counts derived from them, as the real signal. Data health has the measurements.
Top contributors
Pushes, PRs, issues, reviews and comments — stars and forks excluded, so this is contribution rather than popularity
Recent activity
Latest issues, pull requests and releases
- Pull request#142RexDiablo2026-02-23 17:18
- Issue comment#140DanielDecker2026-01-06 16:10Installation breaks on libgpio2 installation on Trixy
- Pull request#141DanielDecker2026-01-06 16:02
- Issue comment#140rkoshak2025-12-23 14:59Installation breaks on libgpio2 installation on Trixy
- Issue comment#140DanielDecker2025-12-14 16:13Installation breaks on libgpio2 installation on Trixy
- Issue#140rkoshak2025-11-23 01:31Installation breaks on libgpio2 installation on Trixy
- Issue comment#139DanielDecker2025-11-18 17:15Swap EightRelayHAT library
- Issue comment#138rkoshak2025-09-26 14:50Allow MQTT TLS connection without specifying CA certificate
- Pull request#138rkoshak2025-09-26 14:50
- Pull request#138pailloM2025-09-26 03:40
- Pull request#137rkoshak2025-05-30 19:41
- Issue comment#136DanielDecker2025-05-18 17:54add type annotations + fix service requirement unknown
- Issue comment#136rkoshak2025-05-15 16:36add type annotations + fix service requirement unknown
- Pull request#136rkoshak2025-05-15 16:35
- Issue comment#136DanielDecker2025-04-25 16:04add type annotations + fix service requirement unknown
- Issue comment#136rkoshak2025-04-22 17:37add type annotations + fix service requirement unknown
- Issue comment#136DanielDecker2025-04-13 07:33add type annotations + fix service requirement unknown
- Issue comment#136DanielDecker2025-04-04 16:11add type annotations + fix service requirement unknown
- Issue comment#136rkoshak2025-04-01 19:28add type annotations + fix service requirement unknown
- Pull request#136DanielDecker2025-03-30 12:58
- Pull request#135rkoshak2025-02-12 20:53
- Pull request#135mayerpro2025-02-09 10:20
- Issue comment#113rkoshak2024-06-03 14:35Convert to a module
- Issue#113rkoshak2024-06-03 14:35Convert to a module
- Issue#128rkoshak2024-06-03 14:34use ColorHSV class from utils.py for i2c.pwm actuator
Totals cover only the window loaded into ClickHouse and count events, not GitHub's lifetime totals — 7 stars here means stars gained during the window, not the repo's star count.